View SP6831EK_236414.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
SP6830/6831
Low Power Voltage Inverters With Shutdown
FEATURES s 99.9% Voltage Conversion Efficiency s +1.15V to +5.3V Input Voltage Range s Inverts Input Supply Voltage s 70A Supply Current for the SP6830 s 200A Supply Current for the SP6831 s 35kHz Operating Frequency for the SP6830 s 120kHz Operating Frequency for the SP6831 s <1A Shutdown Current s 6-pin SOT23-6 Package s Ideal for +3.6V Lithium Ion Battery Applications s Reverse +3.6V Lithium Ion Battery Protection s 25mA Output Current s 19 Output Resistance
APPLICATIONS s Small LCD Negative Bias Voltage s Power Amplifier Negative Bias Voltage s +5V to -5V Voltage Conversion
DESCRIPTION The SP6830/6831 devices are CMOS Charge Pump Voltage Inverters that can be implemented into designs which require a negative voltage from a battery voltage source as low as +1.15V or a power supply rail voltage as high as +5.3V. The SP6830/6831 devices are ideal for both battery-powered and board level voltage conversion applications with a typical operating current of 70A for the SP6830 and 200A for the SP6831. These devices combine an ultra-low shutdown current of <1A with high efficiency (>95% over most of its load-current range) which are ideal for designs using batteries such as cell phones, PDAs, medical instruments, and other portable equipment. The SP6830/6831 devices are available in a space-saving 6-pin SOT23-6 Package.
VOUT 1 VIN 2 C13 SP6830 SP6831
6 C1+ 5 SHDN 4 GND
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
1
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. VIN.........................................................-0.3V to +5.6V VOUT......................................................-5.6V to +0.3V IOUT......................................................................50mA Storage Temperature.......................-65OC to +150OC Lead Temperature (Soldering)..........................300OC Power Dissipation Per Package
6-pin SOT (derate 4.35mW/OC above +70OC)............400mW
SPECIFICATIONS
VIN = +5V, C1=C2=C3=3.3F for the SP6830, C1=C2=C3=1F for the SP6831, and TAMB=-40C to +85C unless otherwise noted. Typical values are taken specifically at TAMB=+25C.
PARAMETER Supply Voltage Range, VDD Supply Current, IVIN Guaranteed Start-up Voltage Shutdown Input Voltage HIGH LOW Shutdown Supply Current Oscillator Frequency, fOSC Output Resistance Voltage Conversion Efficiency Power Efficiency (Ideal) Power Efficiency (Actual)
MIN. 1.15
TYP.
MAX. 5.3
UNITS V A V V A kHz % % % RL = 1k SP6830 SP6831
CONDITIONS
70 200
150 400 1.8
RL = 1k, NOTE1 VIN = VMIN to VMAX VIN = VMIN to VMAX SHDN = GND, VIN = 5V, NOTE 2 SP6830 SP6831 IOUT = 5mA to 25mA, NOTE 3 RL = open RL = 1k, NOTE 4 RL = 1k, NOTE 5
1.5 0.1 24.5 70 35 120 19 95 99.9 98 96
VIN 0.5 1.0 56.3 200 45
Note 1: Minimum VIN required for VO = -VIN +0.2V. Note 2: During the shutdown mode, VIN is disconnected from VOUT. Note 3: Capacitors are approximately 20% of the output impedance where ESR =
1 fOSC x C
.
Note 4: Power Efficiency (Ideal) =
VOUT x IOUT -VIN x (-VIN/RL) VOUT x IOUT VIN x IIN
(c) Copyright 2000 Sipex Corporation
Note 5: Power Efficiency (Actual) =
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
2
PINOUT
PIN ASSIGNMENTS Pin 1-- VOUT -- Inverting charge pump output.
VOUT 1 VIN 2 C13 SP6830 SP6831
6 C1+ 5 SHDN 4 GND
Pin 2 -- VIN -- Input to the positive power supply. Pin 3 -- C1- -- Negative terminal to the charge pump capacitor. Pin 4 -- GND -- Ground reference. Pin 5 -- SHDN -- Active LOW Shutdown input. Pin 6 -- C1+ -- Positive terminal to the charge pump capacitor.
VIN C3
2
VIN
4-Phase Clock SD
ON OFF
5 SHDN
Shutdown
SP6830 SP6831
C1+ 6 C1
4 GND
Comparator
VEE*
Pump Switches
VOUT
SD *VEE = the lower voltage of VOUT and GND
C1VOUT
3 1
VOUT C2 RL
DEVICE C1 SP6830 3.3F SP6831 1F
C2 3.3F 1F
C3 3.3F 1F
fOSC 35kHz 120kHz
Figure 1. Voltage Inverter Circuit for the SP6830/6831
Rev. 9-22-00 SP6830/6831 Low Power Voltage Inverters With Shutdown (c) Copyright 2000 Sipex Corporation
3
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = +5.0V, C1 = C2 = C3 = 3.3F for SP6830, C1 = C2 = C3 = 1F for SP6831, and TAMB = 25OC unless otherwise noted. The SP6830/6831 devices use the circuit found in Figure 17 when obtaining the following typical performance characteristics (unless otherwise noted).
40 35
30 25 20 15 10 5 0 -40
Output Resistance(Ohms)
30 25 20 15 10 5 0 2 2.5 3 3.5 4 4.5 5 5.5 Supply Voltage(V)
Output Resistance(Ohms)
-15
10
35
60
85
Temperature(C)
Figure 2. Output Resistance vs. Supply Voltage
Figure 3. Output Resistance vs. Temperature
50
175 150 125
40
Frequency(kHz)
30
Frequency (kHz)
2 2.5 3 3.5 4 4.5 5 5.5
100 75 50 25
20
10
0 Supply Voltage(V)
0 2 2.5 3 3.5 4 4.5 5 5.5 Supply Voltage(V)
Figure 4. Charge Pump Frequency vs. Supply Voltage for the SP6830
Figure 5. Charge Pump Frequency vs. Supply Voltage for the SP6831
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
4
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = +5.0V, C1 = C2 = C3 = 3.3F for SP6830, C1 = C2 = C3 = 1F for SP6831, and TAMB = 25OC unless otherwise noted. The SP6830/6831 devices use the circuit found in Figure 17 when obtaining the following typical performance characteristics (unless otherwise noted).
50
175 150
40
Frequency (kHz) Frequency (kHz)
125 100 75 50 25
30
20
10
0 -40
-15
10
35
60
85
Temperature(C)
0 -40
-15
10
35
60
85
Temperature(C)
Figure 6. Charge Pump Freqency vs. Temperature for the SP6830
Figure 7. Charge Pump Freqency vs. Temperature for the SP6831
125
300
100
250
Supply Current (mA)
Supply Current (A)
2 2.5 3 3.5 4 4.5 5 5.5
75
200 150 100 50
50
25
0 Supply Voltage(V)
0 2 2.5 3 3.5 4 4.5 5 5.5 Supply Voltage(V)
Figure 8. Supply Current vs. Supply Voltage for the SP6830
Figure 9. Supply Current vs. Supply Voltage for the SP6831
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
5
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = +5.0V, C1 = C2 = C3 = 3.3F for SP6830, C1 = C2 = C3 = 1F for SP6831, and TAMB = 25OC unless otherwise noted. The SP6830/6831 devices use the circuit found in when obtaining the following typical performance characteristics (unless otherwise noted).
500 450 400
Output Ripple (mVP-P)
250
200
Output Ripple (mVP-P)
350 300 250 200 150 100 50 0 0 10 20 30 40 Capacitance (uF)
VIN = 3.3V, VOUT = -2.5V VIN = 2V, VOUT = -1.5V VIN = 5V, Vout = -4V
150
100
VIN = 5V, VOUT = -4V
50
VIN = 3.3V, VOUT = -2.5V VIN= 2V, VOUT= -1.5V
0 0 10 20 Capacitance (uF)
Figure 11. Output Voltage Ripple vs. Capacitance for the SP6831
30
40
Figure 10. Output Voltage Ripple vs. Capacitance for the SP6830
70 60
Output Current (mA)
VIN= 5V, VOUT = -4V VIN = 5V, VOUT= -4V
70 60
VIN= 5V, VOUT = -4V
Output Current (mA)
50 40 30 20 10 0 0 10 20 30 Capacitance (uF) 40
ViN= 2V, VOUT = -1.5V VIN= 3.3V, VOUT = -2.5V
50 40 30 20 10 0 0 10 20 Capacitance (uF) 30 40
ViN= 2V, VOUT = -1.5V VIN = 3.3V, VOUT = -2.5V
Figure 12. Output Current vs. Capacitance for the SP6830
Figure 13. Output Current vs. Supply Voltage for the SP6831
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
6
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN = +5.0V, C1 = C2 = C3 = 3.3F for SP6830, C1 = C2 = C3 = 1F for SP6831, and TAMB = 25OC unless otherwise noted. The SP6830/6831 devices use the circuit found in when obtaining the following typical performance characteristics (unless otherwise noted).
100
Power Efficiency (%)
95
VIN = 3.3V ILOAD = 5mA VOUT = -3.2
90
85
80
75 0 5 10 15 20 25 Output Current(mA)
Figure 14. Power Efficiency vs. Output Current Figure 15. Output Noise and Ripple for the SP6830
VIN = 3.3V ILOAD = 5mA VOUT = -3.2V
Figure 16. Output Noise and Ripple for the SP6831
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
7
VOUT VIN C2 RL
1
6
C1+ SHDN GND
2 SP6830 5 C1SP6831 3 4
C3 C1
Figure 17: SP6830/6831 Connected as a Voltage Inverter in its Typical Operating Circuit; this Circuit Was Used to Obtain the Typical Performance Characteristics Found in Figures 2 Through 16 (unless otherwise noted)
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
8
DESCRIPTION The SP6830/6831 devices are CMOS Charge Pump Voltage Converters that can be used to invert a +1.15V to +5.3V input voltage. These devices are ideal for designs involving batterypowered and/or board level voltage conversion applications. The typical operating frequency of the SP6830 is 35kHz. The typical operating frequency of the SP6831 is 120kHz. The SP6830 has a typical operating current of 70A and the SP6831 operates at 200A. Both devices can output 25mA with a voltage drop of 500mV. The devices are ideal for LCD panel bias applications, cellular phones, pagers, PDAs, medical instruments, and other portable battery-powered equipment. The SP6830/6831 devices combine a high efficiency (>95% over most of its loadcurrent range) with a low quiescent current. THEORY OF OPERATION The SP6830/6831 devices should theoretically produce an inverted input voltage. In real world applications, there are small voltage drops at the output that reduce efficiency. The circuit of an ideal voltage inverter can be found in Figure 18. The voltage inverters require two external capacitors to store the charge. A description of the two phases follows: Phase 1 In the first phase of the clock cycle, switches S2 and S4 are opened and S1 and S3 closed. This connects the flying capacitor, C1, from VIN to ground. C1 charges up to the input voltage applied at VIN. Phase 2 In the second phase of the clock cycle, switches S1 and S3 are opened and S2 and S4 are closed. This connects the flying capacitor, C1, in parallel with the output capacitor, C2. The charge stored in C1 is now transferred to C2. Simultaneously, the negative side of C2 is connected to VOUT and the positive side is connected to ground. With the voltage across C2 smaller than the voltage across C1, the charge flows from C1 to C2 until the voltage at the VOUT equals -VIN.
VOUT = -VIN VIN
S1 C1 S3
S2 C2 VOUT
S4
Figure 18. Circuit for an Ideal Voltage Inverter
Charge-Pump Output The output of the SP6830/6831 devices is not regulated and therefore is dependent on the output resistance and the amount of load current. As the load current increases, losses may slightly increase at the output and the voltage may become slightly more positive. The loss at the negative output, VLOSS, equals the current draw, IOUT, from VOUT times the negative converter's source resistance, RS: VLOSS = IOUT x RS. The actual inverted output voltage at VOUT will equal the inverted voltage difference of VIN and VLOSS: VOUT = -(VIN - VLOSS). Efficiency Theoretically, the total power loss of a switched capacitor voltage converter can be summed up as follows:
PLOSS = PINT + PCAP + PCONV,
where PLOSS is the total power loss, PINT is the total internal loss in the IC including any losses in the MOSFET switches, PCAP is the resistive loss of the charge pump capacitors, and PCONV is the total
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
9
conversion loss during charge transfer between the flying and output capacitors. These are the three theoretical factors that may effect the power efficiency of the SP6830/6831 devices in designs. Any internal losses come from the IC's on board circuitry. Losses in the IC can be induced by the input voltage, the frequency of the oscillator, and the ambient temperature. The most influential internal loss in the IC may be found in the poweron resistance of the internal MOSFET switches. Any of the losses with the charge pump capacitors will be induced by the capacitor's ESR. The affects of the ESR losses and the output resistance can be found in the following equation: IOUT2 x ROUT = PCAP + PCONV and ROUT 4 x (2 x RSWITCHES + ESRC1) + 1 ESRC2 + fOSC x C1 , where IOUT it the output current, ROUT is the circuit's output resistance, RSWITCHES is the internal resistance of the MOSFET switches, ESRC1 and ESRC2 are the ESR of their respective capacitors, and fOSC is the oscillator frequency. This term with fOSC is derived from an ideal switchedcapacitor circuit as seen in Figure 19. Any losses due to the conversion process will happen during the charge transfer between the flying capacitor, C1, and the output capacitor, C2, when there is a voltage difference between them. PCONV can be determined by the following equation: PCONV = fOSC x [ 1/2 x C1 x (VIN2 - VOUT2) +
1
where POUT = VOUT x IOUT and PIN = VIN x IIN where POUT is the power output, VOUT is the output voltage, IOUT is the output current, PIN is the power from the supply driving the SP6830/ 6831 devices, VIN is the supply input voltage, and IIN is the supply input current. Ideal Efficiency The ideal efficiency is not the true power efficiency because it does not involve the input power which includes the input current losses in the charge pump. The ideal efficiency can be determined with the following equation:
Efficiency (ideal) =
POUT x 100% , POUT(IDEAL)
where
POUT(IDEAL) = -VIN x -VIN , RL
f V+ VOUT
C1
C2
RL
/2 x C2 x (VRIPPLE2 - 2VOUTVRIPPLE) ].
V+
Requivalent VOUT
Actual Efficiency To determine the actual efficiency of the SP6830/ 6831 device operation, a designer can use the following equation:
Requivalent =
1 f x C1
C2
RL
Efficiency (actual) = POUT x 100% , PIN
Figure 19. Equivalent Circuit for an Ideal Switched Capacitor
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
10
and POUT is the the power output. Both efficiencies are provided to designers for comparison. APPLICATION INFORMATION For the following applications, C1 = C2 = C3 = 3.3F for the SP6830 and C1 = C2 = C3 = 1.0F for the SP6831. Capacitor Selection Low ESR capacitors are needed to obtain low output resistance. Refer to Table 1 for some suggested low ESR capacitors. The output resistance of the SP6830/6831 devices is a function of the ESR of C1 and C2. This output resistance can be determined by the equation previously provided in the Efficiency section: ROUT 4 x (2 x RSWITCHES + ESRC1) + 1 ESRC2 + fOSC x C1 , where ROUT is the circuit's output resistance, RSWITCHES is the internal resistance of the MOSFET switches, ESRC1 and ESRC2 are the ESR of their respective capacitors, and fOSC is the oscillator frequency. This term with fOSC is derived from an ideal switched-capacitor circuit as seen in Figure 19. Minimizing the ESR of C1 and C2 will minimize the total output resistance and will improve the efficiency.
Flying Capacitor Decreasing flying capacitor, C1, values will increase the output resistance of the SP6830/ 6831 devices while increasing C1 will reduce the output resistance. There is a point where increasing C1 will have a negligible effect on the output resistance due to the the domination of the output resistance by the internal MOSFET switch resistance and the total capacitor ESR. Output Capacitor Increasing output capacitor, C2, values will decrease the output ripple voltage. Reducing the ESR of C2 will reduce both output ripple voltage and output resistance. If higher output ripple can be tolerated in designs, smaller capacitance values for C2 should be used with light loads. The following equation can be used to calculate the peak-to-peak ripple voltage:
VRIPPLE = 2 x IOUT x ESRC2 +
IOUT fOSC x C2 .
Input Bypass Capacitor The bypass capacitor at the input voltage will reduce AC impedance and the impact of any of the SP6830/6831 device's switching noise. It is recommended that for heavy loads a bypass capacitor approximately equal to the flying capacitor, C1, be used. For light loads, the value of the bypass capacitor can be reduced.
SIPEX PART NUMBER SP6830 SP6830 SP6830 SP6831 SP6831 SP6831
MANUFACTURER/ TELEPHONE # KEMET / 864-963-6300 SPRAGUE / 207-324-4140 TDK / 847-803-6100 AVX / 843-448-9411 KEMET/ 864-963-6300 TDK / 847-803-6100
PART NUMBER T494B335*020 595D335X0035 C3216X5R1A335K 0805ZC105K C0805C105KRAC C2012X5R1A105K
CAPACITANCE / VOLTAGE 3.3F / 20V 3.3F / 35V 3.3F / 10V 1F / 10V 1F / 10V 1F / 10V
MAX ESR @ 100kHz 1.5 2.0 0.04 0.04 0.05 0.05
CAPACITOR SIZE/TYPE Case B / Tantalum Case C / Tantalum 1206 / X5R 0805 / X7R 0805 / X7R 0805 / X5R
Table 1. Suggested Low ESR Surface Mount Capacitors
Rev. 9-22-00 SP6830/6831 Low Power Voltage Inverters With Shutdown (c) Copyright 2000 Sipex Corporation
11
+VIN
IN 2 C1+ 2 C1+
IN 2 C1+
IN
RTOT
6 4
C1
GND
SP6830 SP6831 "1"
1 OUT
6 4
C1
GND
SP6830 SP6831 "2"
1 OUT
6 4
C1
GND
SP6830 SP6831 "n"
1 OUT
C1-
3
C1-
3
C1-
3
SHDN 5
SHDN 5
SHDN 5
VOUT
Shutdown Control Input
VOUT = -VIN RTOT = ROUT where VOUT = output voltage, n VIN = input voltage, RTOT = total resistance of the devices connected in parallel, ROUT = the output resistance of a single device, and n = the total number of devices connected in parallel.
C2 x n
Figure 20. SP6830/6831 Devices Connected in Parallel to Reduce Total Output Resistance
+VIN
IN 2 C1+ 2 C1+ SHDN 5 GND IN 2 SHDN 5 C1+ GND IN SHDN 5
6 4
C1
GND
SP6830 SP6831 "1"
5 4
SP6830 SP6831 "2"
3 4
C1
1 OUT
C1
1 OUT
SP6830 SP6831 "n"
C1-
3
C1-
3
C1-
5
1
OUT
VOUT
C2
C2
C2
VOUT = -n x VIN where VOUT = output voltage, VIN = input voltage, and n = the total number of cascaded devices connected.
Figure 21. SP6830/6831 Devices Cascaded to Increase Output Voltage
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
12
When loading the SP6830/6831 devices from IN to OUT, the input current remains constant (disregarding any spikes due to internal switching). Implementing a 0.1F bypass capacitor should be sufficient. When loading the SP6830/6831 devices from OUT to GND, the current from the supply will switch from twice that of IOUT and zero amperes. Designers should implement a large bypass capacitor (C3 = C1) if the supply has a high AC impedance. Voltage Inverter A designer can find the most common application for the SP6830/6831 devices in Figure 17 as a voltage inverter. The only external components needed are 3 capacitors: the flying capacitor, C1, the output capacitor, C2, and the bypass capacitor, C3 (if necessary). This circuit is used to obtain the Typical Performance Characteristics found in Figures 2 to 16 (unless otherwise noted). Connecting in Parallel A designer can parallel a number of SP6830/ 6831 devices to reduce the output resistance for specific designs. All devices will need their own flying capacitor, C1, but a single output capacitor will serve all of the devices connected in parallel by increasing the capacitance of C2 by a factor of n where n equals the total number of devices connected. This connection can be found in Figure 20. Cascading Devices A designer can cascade SP6830/6831 devices to produce a larger inverted voltage output. Refer to Figure 21 for this circuit connection. With two cascaded devices, the unloaded output voltage is decreased by the output resistance of the first device multiplied by the quiescent current of the second device connected. The total output resistance is greatly increased when more than two devices are cascaded. Driving Excessive Loads The output should never be pulled above ground. A designer should implement a Schottky diode (1N5817) from OUT to GND when driving heavy loads where a higher supply is sourcing current into OUT. Refer to Figure 22 for this circuit connection.
GND
4
SP6830 SP6831
1
OUT
1N5817
Figure 22. Protection for Heavy Loads
Combining a Doubler and Inverter Circuit A designer can connect a SP6830/6831 device in a combination doubler/inverter circuit as seen in Figure 23. The doubler uses C3 and C4 while the inverter uses capacitors C1 and C2. Loading either output decreases both output voltages to GND because both the doubler and the inverter circuits use the charge pump. Designers should not allow the total current output from the doubler and the inverter to exceed 40mA. Implementing Shutdown The SP6830/6831 devices are enabled when the SHDN input pin is driven HIGH and disabled when driven LOW. This input must be tied to VIN or GND to minimize any noise effects due to the internal switching of these devices. The SHDN input cannot be driven 0.5V above VIN without the possibility of introducing significant current flows. Layout and Grounding Designers should make an effort to minimize noise by paying special attention to the circuit layout with the SP6830/6831 devices. External components should be connected in close proximity to the device and a ground plane should be implemented. This will keep electrical traces short minimizing parasitic inductance and capacitance.
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
13
C3
+VIN
D1 IN 2
D1 = D2 = 1N4148 D2
VOUT1
C4
C1+ GND C1 C1Shutdown Control Input SHDN
6 4
SP6830 SP6831
3 5
1
OUT
VOUT2
C2
VOUT1 = (2 x VIN) - VFD1 - VFD2 VOUT2 = -VIN where VOUT1 = positive doubled output voltage, VIN = input voltage, VFD1 = forward bias voltage across D1, VFD2 = forward bias voltage across D2, and VOUT2 = inverted output voltage.
Figure 23. SP6830/6831 Device Connected in a Doubler/Inverter Combination Circuit
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
14
PACKAGE: SOT23-6
b C L e
E
e1 D C L A A2
A
C L a 0.20
DATUM 'A'
C A1
A .10
E1
L
2
SYMBOL A A1 A2 b C D E E1 L e e1 a
MIN 0.90 0.00 0.90 0.25 0.09 2.80 2.60 1.50 0.35 0.95ref 1.90ref 0
O
MAX 1.45 0.15 1.30 0.50 0.20 3.10 3.00 1.75 0.55
10
O
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
15
ORDERING INFORMATION
Model Temperature Range Package Type
SP6830EK . ............................................ -40C to +85C ............................................... SOT23-6 SP6830EK/TR ......................................... -40C to +85C ............................................... SOT23-6 SP6831EK . ............................................ -40C to +85C ............................................... SOT23-6 SP6831EK/TR ......................................... -40C to +85C ............................................... SOT23-6
Please consult the factory for pricing and availability on a Tape-On-Reel option.
Corporation
SIGNAL PROCESSING EXCELLENCE
Sipex Corporation Headquarters and Sales Office 22 Linnell Circle Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: sales@sipex.com Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others.
Rev. 9-22-00
SP6830/6831 Low Power Voltage Inverters With Shutdown
(c) Copyright 2000 Sipex Corporation
16

▲Up To Search▲

Price & Availability of SP6831EK

	To Download SP6831EK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .